ProductsButton1.gif


Alley Cat Allies

Alley Cat Allies



Alley Cat Allies

Alley Cat Allies

Cat House on the Kings
Back to Ketch-ALL Poles

KETCH-ALL PARTS LIST, PARTS PRICE LIST & REPAIR INSTRUCTIONS

Catch pole repair parts

1. release knob (kit KR1)
2. grips (KR2)
3. tubing
4. chuck (Kit KR4)
5. toothguard (KR5)
6. allen set screw		 7. head lock ring (Kit KRHD)
8. collar (Kit KRHD)
9. head (Kit KRHD)
10. steel cable (Kits KRC)
16. release knob lock washer (Kit KR1)
17. compression washer (Kit KRLD)		 18. step washer (Kit KRLD)
19. compression spring (Kit KRLD)
20. cage (Kit KRLD)
21. 9/32 ball bearings (Kit KRLD)
22. chuck ring (ext. pole only) (Kit KR4)
23. hair guard (Kit KRHD)
PRICE LIST FOR REPLACEMENT PARTS

Item # DESCRIPTION UNIT PRICE Order
KRLD locking device - with cage (#20) ball bearings (#21), washers (#16, #17, #18) and spring (#19) (designate kit for standard or extension pole)
Click here for picture		 $14.00
Please choose Stnd. or Ext. Pole:
QTY: 
KTG tooth guard (fits all poles) (#5)
Click here for picture		 $5.50
QTY:
KR1 release knob (#1) - with washer (#16) (designate if for standard or extension pole)
Click here for picture		 $9.50
Please choose Stnd. or Ext. Pole:
QTY: 
KHC28 head (#9) - complete with hairguard (#23), lock ring (#7) and collar (#8) for 28" and 3' poles
Click here for picture		 $23.00
QTY:
KHC4 head (#9) - complete with hairguard (#23), lock ring (#7) and collar (#8) for 4', 5' and 4'-6' ext. poles
Click here for picture		 $23.00
QTY:
KHC7 head (#9) - complete with hairguard (#23), lock ring (#7) and collar (#8) for 7'-12' ext. pole
Click here for picture		 $23.00
QTY:
KR2 hand grip (#2) (designate if for standard or extension pole)
Click here for picture		 $4.50
Please choose Stnd. or Ext. Pole:
QTY: 
KR4 chuck (#4) with lock ring (for extension pole) (#22) $16.00
QTY:


Replacement cables complete - with spring, ball and plastic
Plastic Coated Aircraft Wire
(all cables come ready to install)
Click here for picture
Item # SIZE / DESCRIPTION UNIT PRICE Order
KRC28 for 28 inch baton-type Ketch-All Pole $20.00
QTY:
KRC3 for 3 feet standard Ketch-All Pole $21.00
QTY:
KRC4 for 4 feet standard Ketch-All Pole $23.00
QTY:
KRC5 for 5 feet standard Ketch-All Pole $25.00
QTY:
KRC6 for 4-6 feet extension Ketch-All Pole $26.00
QTY:
KRC12 or 7-12 feet extension Ketch-All Pole $35.00
QTY:

INSTRUCTIONS FOR REPAIR OF ALL KETCH-ALL POLES
(Refer to Parts List above for Parts Numbers)
TO REMOVE CABLE
1. Remove large lock ring #7 located behind collar #8.
2. Pull collar #8 back toward rear of pole until head #9 is exposed. Note: it may be necessary to slide tooth guard #5 back in order to pull collar back.
3. Remove head #9, which is right hand thread, leaving collar #8 on pole. IF APPLICABLE: remove allen set screw #6 (with allen wrench)located on head.
4. When head #9 is free, pull release knob #1 back and hold in this position (we suggest using vice grips) while pulling cable out through the other end of pole.
5. Pull cable spring from hair guard #23
TO INSTALL CABLE
1. Insert ball of cable through hair guard (which should be attached to head shank #9), running cable through until hair guard #23 meets cable spring.
2. Screw hair guard #23 into cable spring. The cable is now ready to install.
3. Insert cable through tubing #3, pulling back on release knob #1 to allow cable to pass through locking device.
4. Screw head onto end of pole.
5. Insert cable ball in groove or track in head #9
6. Pull collar #8 over head and cable ball, and replace lock ring #7.
7. IF APPLICABLE: replace set screw #6
TO DISASSEMBLE LOCKING DEVICE
1. Pull back on release knob #1, turning it until hole in tubing lines up with hole in cage #20.
2. Insert ice pick or nail through holes, thus keeping locking device from turning.
3. Remove release knob #1, which is a right hand thread. There should be a lock washer #16 inside release knob.
4. Remove: lock ring #17, step washer #18, compression spring #19, cage #20 and three ball bearings #21.
TO REPLACE HEAD
To replace head, follow steps under headings: To Remove Cable and To install Cable above.   You will damage about one inch of cable spring when you pull the old head off.   This should be cut off to enable you to screw the new hair guard into the part of the spring that remains intact.